Applied Biosystems GeneAmp PCR System 9700 User Manual Download Page 103

Page: 103 / 132

Troubleshooting 8-3

Display Screen Error Messages

Error Messages

Table

Refer to the following table for a description of error messages, and recommended
actions that you should take.

Table 8-1

Error Messages

Message

Description

Recommended Action

Battery RAM version number
lost

This error is generated when the battery RAM has
been lost and re-initialized.

Call Technical Support.

Block Calibration initialized

Software or hardware failure.

Call Technical Support.

Block Calibration reset to
default

System error.

Block data reset to defaults.

Call Technical Support.

Block isn’t configured

The instrument has defaulted to a 96-well
configuration.

Call Technical Support.

Block initialized

Block module has been re-initialized.

Call Technical Support.

Block version unknown,
update firmware

The calibration data in the block is not recognized by
the firmware.

Upgrade the firmware.

Bus Error

System error.

Call Technical Support.

Calibration battery RAM
initialized

Calibration lost. Instrument may not perform to
specification.

Call Technical Support.

Can only enter an infinity hold
at end

A method can only have a HOLD segment with an
infinity hold as the last segment in a method.

This message occurs when you try to enter an infinity
hold segment in the middle of a method.

Assign finite time segments
to holds within a method.

Can’t allocate timer

System error.

Call Technical Support.

Delete your methods first

User tried to delete a user name that has methods
stored under it.

Delete or transfer the
associated methods before
deleting a user name.

Enter a name or CANCEL

You did not enter at least one character on the User
Name screen before pressing the Accept key.

Enter the user name to
which the desired method is
assigned.

Enter oligo sequence

Incomplete TmCalc data.

Enter a value in the P1P2
fields of the TmCalc.

Enter user and method names
or CANCEL

You did not enter a user name and a method name
before storing a method.

Specify the method name
and choose a user to store a
method.

FATAL – Block shut off by
hardware

Block thermal runaway.

Call Technical Support.

FATAL – Block thermal runway

Fatal error.

Turn off system.

Call Technical Support.

FATAL – Cover shut off by
hardware

Heated cover thermal runaway.

Call Technical Support.

FATAL – Heat sink is too hot

Ambient conditions may be too warm.

Call Technical Support.

FATAL – Heat sink sensor
failure

System error.

Call Technical Support.

FATAL – Heated cover thermal
runaway

Fatal error.

Turn off system.

Call Technical Support.

Summary of Contents for GeneAmp PCR System 9700





































































































































Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands

Applied Biosystems GeneAmp PCR System 9700, User Manual

Search results

Summary of Contents for GeneAmp PCR System 9700

Reviews:

Related manuals for GeneAmp PCR System 9700

Brands by name

Popular brands