manualshive.com logo in svg

Ansul AutoPulse Z-28, Instructions Manual

Share
Download
Ansul AutoPulse Z-28 Instructions Manual Download Page 150

A-2

Device Types

Sensor/Base Device 
Types

The hardware device type used for a specific sensor/base combination depends on the 
combination.  The following table summarizes which point types can be used with the various 
combinations of sensor and base.  

To use this table, first identify the exact sensor/base combination in use for each SLCnet point.  
The point at which the column (base) and row (sensor) intersect contains the device type that 
you should use for that sensor/base combination.

IAMs / ZAMs / SLCnet 
Addressable Device 
Types

The following table lists the PIDs and corresponding device types for IAMs, ZAMS, and 
SLCnet Addressable devices.

Table A-1. Sensor/Base Device Types

Standard 

Base 

430636

LED Base 

430637

Sounder 

Base

Isolator 

Base 

430640 

External 

Duct Base 

430649 
430650 

Relay Base 

430638

Photo Sensor 

PHOTO

XPHOTO

SPHOTO

XSPHOTO

IPHOTO

XIPHOTO

PHOTO

RPHOTO
XPHOTO

RPHOTO

XRPHOTO

Ion Sensor 430632

ION

SION

IION

N/A

RION

Heat Sensor 430633

HEAT

OHEAT

SHEAT

SOHEAT

IHEAT

IOHEAT

N/A

RHEAT

ROHEAT

Table A-2. IAM/ ZAM/ SLCnet Addressable Device Types

Device

PID

Device Type

SLCnet Class A Monitor ZAM

430666

MAZAM

SLCnet Class B Monitor ZAM

430665

MBZAM

SLCnet Single Action Pull Station

Standard -- 430660
Break Glass -- 430664

ADRPUL

SLCnet Supervised IAM

430660

IAM

SLCnet Relay IAM

430664

RIAM

AUTOPULSE Z-28 ExtA SLCnet Addressable NAC 
Device with 4 NACs

430674

AUTOPULSE 
Z-28 ExtA

AUTOPULSE Z-28 ExtA SLCnet Addressable and a 
Repeater NAC Device with 4 NACs

 430674

RAUTOPULS
E Z-28 ExtA8

Summary of Contents for AutoPulse Z-28







































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands