Altigen MAX Communication Server ACM 6.0 Administration Manual Download Page 378

Page: 378 / 448

Chapter 27: Microsoft Exchange Integration

366

MAXCS ACM 6.0 Administration Manual

Figure 17. Mail account configuration in Exchange 2003 Administrator

4. Use the preceding steps to double check the synchronization of all mailbox names

used jointly by MAXCS and Exchange 2003 Server.

Enable Exchange Integration in MaxAdmin

To enable the Exchange integration feature in MaxAdministrator:
1. In MaxAdmin, select

System > Voice Mail Configuration

2. On the

Messaging

tab, select the integration option you want.

Figure 18. Voice Mail Configuration window, Exchange Integration panel

3. Enter the IP address or the fully qualified domain name of the Exchange Client

Access Server or the Exchange 2007 Unified Messaging Server, as appropriate, in
the space provided and click

Apply

This completes the configuration for the

Synchronize with Exchange 2003/2007

option. The other two options require some additional configuration. See “Additional

Steps for Bridged Access and Native VM Integration” on page 370.

Summary of Contents for MAX Communication Server ACM 6.0

































































































































































































































































































































































































































































Search results

Summary of Contents for MAX Communication Server ACM 6.0

Reviews:

Related manuals for MAX Communication Server ACM 6.0

Brands by name

Popular brands

Altigen MAX Communication Server ACM 6.0, Administration Manual

Search results

Summary of Contents for MAX Communication Server ACM 6.0

Reviews:

Related manuals for MAX Communication Server ACM 6.0

Brands by name

Popular brands