Altigen MAX Communication Server ACM 6.0 Administration Manual Download Page 204

Page: 204 / 448

Chapter 15: Extension Configuration

192

MAXCS ACM 6.0 Administration Manual

Figure 2. Triton Analog Station Line Properties dialog box

Configure the following hardware extension-specific features:

Parameter

Description

Caller ID Signal
Format

Message format with which to send Caller ID
information:
•

None

•

SDMF

—Single Data Message Format for

supporting and sending a single data type, such
as phone numbers.

•

MDMF

—Multiple Data Message Format for

supporting and sending multiple data types, such
as name and number information. (Default for
US/Canada installation.)

•

DTMF

—Dual Tone Multi-Frequency, composed of

high and low frequencies, for touch tone dialing.

Message Waiting
Signal Type

Type of Message Waiting indicator for the phone set:
•

None

•

FSK/SDMF

—Frequency Shift Keying/Single Data

Message Format indicator.

•

FSK/MDMF

—Frequency Shift Keying/Multiple

Data Message Format indicator. (Default for US/
Canada installation.)

Flash Duration

Specifies the Flash Duration time in milliseconds:
• 85-750 (default)
• 50-600
• 100-700
• 150-800
• 200-900
• 300-1000

Summary of Contents for MAX Communication Server ACM 6.0

































































































































































































































































































































































































































































Search results

Summary of Contents for MAX Communication Server ACM 6.0

Reviews:

Related manuals for MAX Communication Server ACM 6.0

Brands by name

Popular brands

Altigen MAX Communication Server ACM 6.0, Administration Manual

Search results

Summary of Contents for MAX Communication Server ACM 6.0

Reviews:

Related manuals for MAX Communication Server ACM 6.0

Brands by name

Popular brands