manualshive.com logo in svg

Altigen MAX Communication Server ACM 6.0, Administration Manual

The Altigen MAX Communication Server ACM 6.0 is an innovative communication solution. Our Administration Manual provides comprehensive guidance for users, ensuring a seamless experience. Easily download the manual for free from our website, offering step-by-step instructions and valuable insights to optimize your utilization of this exceptional product.

Share
Download
background image

Chapter 11:  Board Configuration

MAXCS ACM 6.0 Administration Manual 119

Configuring the Triton VoIP Board

It is strongly recommended that system administrators review the “Network 

Configuration Guidelines for VoIP” on page 307 before setting up VoIP features.

Overview

VoIP for MAXCS runs on both SIP and H.323 protocols that allow voice calls to be made 
through an IP network. It includes an integrated VoIP gateway to convert voice calls into 

IP packets and transmit them through the IP network. 
MAXCS VoIP uses DSP engines residing on the Triton VoIP board to perform the voice 
coding/decoding functions needed for SIP and H.323 devices.
The Triton VoIP board can be configured as a 12-port G.711/G.723.1/G.729AB or 30-
port G.711 board.
For limitations on configuring Triton VoIP boards and ports see AltiGen’s 

Telephony

 

Hardware Manual

.

Configuration

Double-click the TritonIP board in the 

Boards

 window to open the 

Board Configuration

 

window, similar to Figure 2 on page 116. See attribute descriptions below Figure 2. Note 

the following additional information:

•

Clicking the 

Board Configuration

 button opens a window that displays the board 

serial number, DSP clock, and physical and logical IDs. The drop-down list in the 

Configure Type

 field lets you select between a 12-port G.711/G.723/G.729 

configuration and a 30-port G.711 configuration.

Figure 5. Board Configuration window

Configuring the Triton T1/E1 Board

Overview of the Triton T1/E1 Board

Through MaxAdministrator, the Triton T1/E1 board can be configured for either digital 

T1 CAS (channel associated signaling), T1 PRI (Primary Rate Interface), E1 CAS, or E1 
PRI.
Both T1 CAS and T1 PRI carry 24 channels using time-division multiplexing (TDM) at an 
overall rate of 1.544 Mbps. Voice T1 provides 24 64K channels with robbed bit signaling. 

T1 PRI provides 23 64K channels, using one 64K channel for D channel messaging.
E1 CAS and E1 PRI carry 32 channels using TDM at an overall rate of 2.048 Mbps. Both 
of them provide 30 64K channels for voice.

If you change this configuration, 
you must restart the switching 
services for the change to take 
effect.

Summary of Contents for MAX Communication Server ACM 6.0

































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MAX Communication Server ACM 6.0

Lantronix UDS2100 Quick Start Manual preview
UDS2100
Brand: Lantronix Pages: 6
Lantronix SGX 5150 Manual preview
SGX 5150
Brand: Lantronix Pages: 27
R&S SpycerNode 2U12 User Manual preview
SpycerNode 2U12
Brand: R&S Pages: 136
Xyplex MAXserver 1600 Hardware Installation And Maintenance Manual preview
MAXserver 1600
Brand: Xyplex Pages: 58
IBM System x3500 M2 Type 7839 Installation And User Manual preview
System x3500 M2 Type 7839
Brand: IBM Pages: 126
MRV Communications LX-4000 Series Getting Started preview
LX-4000 Series
Brand: MRV Communications Pages: 65
QNAP TBS-464 User Manual preview
TBS-464
Brand: QNAP Pages: 49
Tandberg Data BizNAS D400 Series Quick Start preview
BizNAS D400 Series
Brand: Tandberg Data Pages: 2
Alcatel-Lucent OmniTouch 8460 Specifications preview
OmniTouch 8460
Brand: Alcatel-Lucent Pages: 4
Habey FW-1042 Quick Setup Manual preview
FW-1042
Brand: Habey Pages: 4
Vitek VT-IPSD102H - Brochure preview
VT-IPSD102H -
Brand: Vitek Pages: 2
Meinberg IMS-M4000 Manual preview
IMS-M4000
Brand: Meinberg Pages: 112
Sierra Wireless ACM Installation And Operation Manual preview
ACM
Brand: Sierra Wireless Pages: 53
W&T 57630 Manual preview
57630
Brand: W&T Pages: 211
IBM 4252E1U Datasheet preview
4252E1U
Brand: IBM Pages: 2
NASdeluxe NDL-2700T+ Installation Manual preview
NDL-2700T+
Brand: NASdeluxe Pages: 6
XVision X101VS User Manual preview
X101VS
Brand: XVision Pages: 100
GIGA-BYTE TECHNOLOGY G591-HS0 User Manual preview
G591-HS0
Brand: GIGA-BYTE TECHNOLOGY Pages: 113

Brands by name

Popular brands

Load more brands