Altigen MAX Communication Server ACM 6.0 Administration Manual Download Page 129 | Manualshive

Page: 129 / 448

background image

Chapter 11: Board Configuration

MAXCS ACM 6.0 Administration Manual 117

Important:

To implement some board configuration changes, you must shut down and
restart by choosing

Services > Shut Down All Services

(which also closes

MAXCS) and then restarting MAXCS. If this is necessary, a message will pop

up telling you so.

Using the Triton Resource Board

The Triton resource board requires no configuration. Board resources are available when

the board is installed.
The resource board has a maximum of 12 bridges for:

•

6-party conferencing. When an extension is trying to make a conference call, the
system will try to use the conference bridge on the resource board first. If conference
bridges on the resource board are all busy, the system will use the conference
bridges on the extension board, analog or VoIP board.

•

Workgroup supervisor silent monitoring, barge-in, and coaching.

For example, if two supervisors are coaching agents, only 10 bridges are left for 6-party
conferencing.

Notes

:

If a supervisor tries to perform silent monitoring, barge-in, or coaching

and there is no

resource board in the system,

the supervisor will hear an

error tone

.

If the supervisor is using an IP phone, then

Connect Voice Stream to Server

should

be checked in the Extension Configuration window so that the system can pull the caller
and agent's voice stream to the resource board to allow the supervisor to tap into the

conversation.

Using the Triton MeetMe Conference Board

The Triton MeetMe conference board requires no configuration. Board resources are
available when it is installed. You do have to assign a MeetMe Conference extension

(select

PBX > MeetMe Conference Configuration

).

One MeetMe conference board is supported in a system.

Note:

In a multiple gateways installation, the MeetMe conference board can be in any
gateway server.

Configuring the Triton Analog Station Board

Double-click the Triton Analog Station board in the

Boards

window to open the

Board

Configuration

window, similar to Figure 2 on page 116. See attribute descriptions

below Figure 2. Note the following additional information:

•

Double-clicking a channel in the

Channel Mapping List

opens a Triton Analog Line

configuration dialog box. See “Triton Analog Station Line Properties” on page 191.

This option is in the
Extension Configuration window

«
...
127
128
129
130
131
...
»

Summary of Contents for MAX Communication Server ACM 6.0

































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MAX Communication Server ACM 6.0

Brand: D-Link Pages: 38

Epress EtherNetwork DP-301P+

Brand: D-Link Pages: 2

Brand: Basalte Pages: 2

Brand: Avaya Pages: 19

Brand: SafeNet Pages: 109

totalstorage 200

Brand: IBM Pages: 180

SUPERSERVER 5018D-FN8T

Brand: Supermicro Pages: 124

Brand: Avaya Pages: 119

Brand: Portwell Pages: 21

Brand: IBM Pages: 98

DLAP-201 Series

Brand: ADLINK Technology Pages: 39

Brand: Patton Pages: 15

eServer BladeCenter HS20Type 8832

Brand: IBM Pages: 112

SuperServer 6123L-8R

Brand: Supero Pages: 105

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

Brand: 2Wire Pages: 2

Brand: Viavi Pages: 7

Brand: Datum Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands