ADVANTEST R3765AG Operation Manual Download Page 12

Page: 12 / 446

R3765/67G Series Network Analyzer Operation Manual

Table of Contents

C-3

7.3.1

Setting Signal Source........................................................................

7-6

7.3.2

Interlocking between Channels .........................................................

7-8

7.4

RESPONSE Block .................................................................................

7-9

7.4.1

Setting Input and Parameter Conversion ..........................................

7-10

7.4.2

Display Data Format .........................................................................

7-14

7.4.3

Setting Display Coordinate Scale......................................................

7-15

7.4.4

Four Screen Display and Display Selection Information ...................

7-16

7.4.5

Display Layout...................................................................................

7-18

7.4.6

Trace Data Selection.........................................................................

7-23

7.4.7

TRACE Operation .............................................................................

7-24

7.4.8

Label Input ........................................................................................

7-25

7.4.9

Colors Settings..................................................................................

7-26

7.4.10 Averaging/Smoothing and Resolution Bandwidth .............................

7-28

7.5

Calibration ..............................................................................................

7-31

7.5.1

Normalizing .......................................................................................

7-31

7.5.2

Normalize & Isolation Calibration ......................................................

7-32

7.5.3

1-Port Full Calibration .......................................................................

7-32

7.5.4

2-Port Full Calibration (R3765CG/67CG only) ..................................

7-34

7.5.5

Calibration Method ............................................................................

7-36

7.5.6

Interpolating Calibration Data............................................................

7-42

7.5.7

Calibration Kit Selection ....................................................................

7-43

7.5.8

Parameters Entry of an User-selected Calibration Kit.......................

7-44

7.5.9

Extending Measurement Reference Plane .......................................

7-47

7.5.10 Calibration Data Clear.......................................................................

7-50

7.5.11 3-Port Full Calibration .......................................................................

7-51

7.5.12 4-Port Full Calibration .......................................................................

7-58

7.6

Marker Function .....................................................................................

7-64

7.6.1

Setting Marker...................................................................................

7-65

7.6.2

Marker Coupling between Channels .................................................

7-66

7.6.3

Interpolation between Measurement Points......................................

7-68

7.6.4

Displaying Marker Read out Value....................................................

7-68

7.6.5

Delta-Marker Function.......................................................................

7-69

7.6.6

Marker Menu during Impedance Measurement ................................

7-72

7.6.7

Marker Analysis Function..................................................................

7-73

7.7

Time Domain Function(OPT 70) ............................................................

7-84

7.7.1

Time Domain Transformation Function.............................................

7-84

7.7.2

Window Processing...........................................................................

7-86

7.7.3

Gate Function....................................................................................

7-87

7.7.4

Time Domain Transformation Mode..................................................

7-88

7.7.5

Transformation of the Time Domain Horizontal Axis.........................

7-88

7.8

CDMA IF Filter Analysis Function ..........................................................

7-89

7.9

Sweep ....................................................................................................

7-93

7.9.1

Setting Sweep Type ..........................................................................

7-93

7.9.2

Editing Segment of User Frequency Sweep .....................................

7-94

Summary of Contents for R3765AG































































































































































































































































































































































































































































Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands

ADVANTEST R3765AG, Operation Manual

Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands