ADVANTEST R3765AG Operation Manual Download Page 56

Page: 56 / 446

R3765/67G Series Network Analyzer Operation Manual

3.4 Basic Measuring Procedure

3-8

3.4

Basic Measuring Procedure

Shows basic measuring procedure of R3765/67G series.

Measuring procedure

Connection

Connect DUT (device under test) to the R3765/67G series.

Setting of the R3765/67G series

Initialize the R3765/67G series by pressing [PRESET] key.

Next, select the setting of the R3765/67G series according to the measurement to
perform.
(If necessary, connect DUT temporarily then.)

Calibration

Acquire the reference of magnitude and phase according to the measurement and
eliminate measurement error.

Measurement

Connect DUT and execute the measurement.

Read the parameter to measure by using marker function, etc.

Measured result output

The measured results can be output to the printer or the plotter with GPIB interface.

Also they can be saved in floppy disk.

Summary of Contents for R3765AG































































































































































































































































































































































































































































Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands

ADVANTEST R3765AG, Operation Manual

Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands