ADVANTEST R3765AG Operation Manual Download Page 59

Page: 59 / 446

R3765/67G Series Network Analyzer Operation Manual

3.5 Measurement Samples of Simple Transmission Characteristics

3-11

3.5.2

Calibration (Normalize)

Calibrate the frequency characteristics of the R3765/67G series.

Remove DUT and connect a through adapter instead.

Press [CAL]

{NORMALIZE (THRU)}.

The display on the screen changes as follows.

CORRECT key is set to ON automatically.

Following the completion, return the connection the DUT (filter).

Figure 3-9 Screen of Frequency Characteristic Normalize

Summary of Contents for R3765AG































































































































































































































































































































































































































































Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands

ADVANTEST R3765AG, Operation Manual

Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands