ADVANTEST R3765AG Operation Manual Download Page 49

Page: 49 / 446

R3765/67G Series Network Analyzer Operation Manual

3.1 Initial Power-on

3-1

BASIC OPERATING GUIDELINES

This chapter explains the fundamental operation for those who use the R3765/67G series for the
first time.

3.1

Initial Power-on

(1)

Connecting to AC Power Source

With the R3765/67G’s power switch turned OFF, connect the attached power cable to
the AC power connector on the rear panel.

CAUTION!
To avoid damage to the analyzer, operate the analyzer within the specified input voltage and
frequency ranges.

Figure 3-1 Connecting the Power Cable

Connect end of the power cable to an outlet.

AC Power Connector

Summary of Contents for R3765AG































































































































































































































































































































































































































































Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands

ADVANTEST R3765AG, Operation Manual

Search results

Summary of Contents for R3765AG

Reviews:

Related manuals for R3765AG

Brands by name

Popular brands