background image

FUEL SYSTEM 3 - 9 

l

 NOTICE: 

The last digit in the identification number of the needle 
indicates the recommended position of the E-clip from the 
top of the needle. 

Example:

           6DH2-3 

       

   

  Throttle slide 

With an opening of the throttle slide between 1/8 and 1/2, the 
dimension on the projection of the slide influences the 
mixture which, during this transition period from low to high 
speed, must be relatively rich. 

Main jet 

The main jet of the carburetor has been selected for a 
temperature of -20°C (O°F), at sea level. Other main jets can 
be installed depending on temperature and/or altitude 
differences. Always refer to spark plug electrode colour 
and/or the piston crown to determine the appropriate jet size 
to be used. 

Adjustment of float level 

In order for the engine to deliver its full power, it is essential 
that the level of the fuel in the carburetor bowl remain at a 
pre-determined level. To verify the proper float level, proceed 
as follows: 

Remove the carburetor bowl and gasket. 

Turn the carburetor upside down, and measure the 
height H between the seat of the bowl and the upper 
end of the float lever. 

Bend the stop flap of the float lever until the 
recommended height has been reached. 

The measured height H must be 23.9 mm 

± 1 mm 

(0.941" ± 0.040"). 

    

 

 

 

Needle 
identification 
number 

Recommended 
position of the  
E-CLIP from the 
top 

 

Shallow cut 

(fast moving 

air) 

Rich Mixture 

Deep cut 

(slow moving 

air) 

Lean Mixture 

 

Float lever 

Level surface 

Float lever stop 

 

Float lever stop 

Summary of Contents for 2002 Snow Hawk














































































































































































Reviews: