manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 44

ABB i-bus

®

 KNX 

Commissioning 
 
 

42   2CDC506083D0201 | JRA/S 6.230.3.1 

3.3.2.2.1 

Output A,B: Switch actuator - Time parameter window 

All settings for the 

Time

 function – 

Staircase lighting, Switching ON/OFF delay

 and 

Flashing

 – are 

undertaken in this parameter window.  

This parameter window is visible if the 

Enable function Time

 parameter is enabled in Output A,B: Switch 

actuator (only "UP" contact

)

 parameter window, p. 38. 

 

 

Explanations of the Time functions and sequences are provided in Planning and application, p. 115. 
Please also observe Function diagram, p. 126, from which the switching and timing priorities originate. 

Note 

Observe the contact life span and switching cycles per minute. 
For the contact life and switching operations per minute, see Technical data, p 7 

 

Time function 

Options: 

Staircase lighting 
Switching ON/OFF delay 
Flashing 

This parameter defines the type of 

Time

 function for each output.  

•

 

Staircase lighting

: The value that switches the staircase lighting on and off can be parametrized. 

The staircase lighting time starts when the function is switched on. It is switched off immediately after 
the staircase lighting time ends. 

Note 

The 

Staircase lighting

 function can also be called via the 

Switch, Logical connection x

 (x = 1, 2) group 

object or with a light scene recall. 

 

•

 

Switching ON/OFF delay

: The output can be switched on or off with a delay via this function. 

•

 

Flashing:

 see Output A,B: Switch actuator - Time, -

 Flashing

 parameter window, p. 47. 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands