manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 123

ABB i-bus

®

 KNX 

Planning and application 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   121 

Setting up a simple automatic sun protection system 

 

Two further components are required in addition to the Blind/Roller Shutter Actuator and the touch sensor 
in order to set up a simple automatic sun protection system: an activation option for the user, e.g. a further 
switch sensor or the second rocker of the UP/DOWN touch sensor, and a brightness sensor. 

Room users can use the second switch sensor to specify whether they wish to use the automatic sun 
protection or would rather control the shutters manually. If the automatic sun protection is activated via 
a switch sensor, the shutter moves automatically until either the automatic sun protection is deactivated 
via the same switch sensor or the user issues a direct Move telegram, e.g. UP/DOWN or Move to position, 
and the automatic function is thus also deactivated. 

The brightness sensor sends the Blind/Roller Shutter Actuator information as to whether there is direct 
sunlight on the window or the façade. Once the adjustable delay period has elapsed, the actuator positions 
the blind according to the set 

Position for sun = 1 (sun)

 or 

Position for sun = 0 (no sun).

 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands