manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 138

ABB i-bus

®

 KNX 

Planning and application 
 
 

136   2CDC506083D0201 | JRA/S 6.230.3.1 

Inputs 

•

 

The inactive waiting time is only active on bus voltage recovery. 

Blind 

The reaction of the blind/shutter output is parametrizable. The output can assume any state or remain 
unchanged. 

Note 

The position of the blind or shutter is also stored in the event of bus voltage failure if the 

Automatic

 

function is activated. The blind or shutter remains in the same position. 
On bus voltage recovery, the position is retained and the group object value is undefined. The value is 
not updated until the next Move telegram. 
If the 

Activation of autom. control

 group object has not been assigned a group address, the 

Automatic

 

function is deactivated when there is a download. 
If Automatic is active, it remains on after a download until the next manual override or until it is 
deactivated by the 

Activation of autom. control

 group object. 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands