manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 109

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   107 

No. 

Function 

Object name 

Data type 

Flags 

77 

Disable function Time 

Output A 

1 bit  

DPT 1.003 

C, W 

This group object is enabled if the 

Enable function Time

 parameter is set to 

Yes

 in the 

Output A,B: Switch actuator

 parameter 

window. 

The group object value on bus voltage recovery can be set using the 

Object value "Disable function Time" on bus voltage 

recovery

 parameter in the 

- Time

 parameter window. 

With the Time function disabled, the output can only be switched on or off; the 

Staircase lighting

 function is not triggered. 

Telegram value  

1 = staircase lighting disabled 
0 = staircase lighting enabled 

The contact position at the time of disabling and enabling is retained and will only be changed with the next switch telegram 
to communication object 

Switch

. 

 

78 

Scene 

Output A 

1 byte 

DPT 18.001 

C, W 

This group object is enabled if the 

Enable function Scene

 parameter is set to 

Yes

 in the 

Output A,B: Switch actuator

 parameter 

window. 

Using this 8-bit group object, a Scene telegram can be sent using a coded telegram. The telegram contains the number of the 
scene concerned as well as the information on whether the scene is to be recalled or if the current contact position is to be 
assigned to the scene. 

Telegram format (1 byte):  MXSSSSSS  

 

(MSB) (LSB) 

 

M: 0 – scene is recalled 

 

1 – scene is stored (if allowed) 

 

X: not used 

 

S: scene number (1-64: 00000000…00111111) 

 

KNX 1 byte telegram value 

Meaning 

Decimal 

Hexadecimal 

00 or 64 

01 or 65 

02 or 66 

… 

63 or 127 

00h or 40h 

01h or 41h 

02h or 42h 

… 

3Fh or 7Fh 

Recall scene 1 

Recall scene 2 

Recall scene 3 

… 

Recall scene 64 

128 or 192 

129 or 193 

130 or 194 

… 

191 or 255 

80h or B0h 

81h or B1h 

82h or B2h 

… 

AFh or FFh 

Store scene 1 

Store scene 2 

Store scene 3 

… 

Store scene 64 

 

For further information see: Scene function, p. 133 and Code table, 8 bit scene, p. 142 

 

79 

Forced operation 

Output A 

1 bit 

DPT 1.003 

C, W 

This group object is enabled if the 

Enable function Forced operation

 parameter is set to 

Yes

 and the 

Object type “Forced 

operation”

 parameter is set to 

1 bit

 in the 

Output A,B: Switch actuator

 parameter window. 

If this group object receives the value 1, the output is forcibly set to the parametrized switch position set in the 

Output A

 

parameter window. The forced positioning of the contact continues until forced operation ends, which it does when a 0 is 
received via the 

Forced operation

 group object.  

Please note that the 

Forced operation

 function and a bus voltage failure have a higher priority on the contact position, 

see Function diagram, p. 126. 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands