manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 103

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   101 

3.4.3.2 

Switch/dimming sensor group objects 

No. 

Function 

Object name 

Data type 

Flags 

10 

Block 

Input a:  

Switch/dimming sensor 

1 bit  

DPT 1.003 

C, W 

This group object is enabled if the 

Enable group object "Block" 1 bit

 parameter is set to 

Yes

 in the 

Input a: Switch/dimming 

sensor

 parameter window. 

Using the communication object 

Block

, the input can be blocked or enabled. With activated communication object 

Block

 the 

inputs are blocked. 

 

Note 

When the input is blocked there is fundamentally no reaction to a signal change on the input, but: 

– Waiting for a long button operation or a minimum signal duration is suspended. 

– Parametrized 

Cyclic sending

 is interrupted with dimming steps. 

– It is still possible to write the 

Switch

 group object. 

When enabling an input, a change of the signal states (as opposed to before the block) leads to immediate 
processing, e.g.: 

– The minimum actuation or detection of a long/short button push starts. 

– Group objects send their value if necessary. 

 

Telegram value: 

0 = enable input a 
1 = Block input a 

 

11 

Switch 

Input a: 

Switch/dimming sensor 

1 bit  

DPT 1.001 

C, W, T 

This group object is enabled if the 

Function

 parameter is set to 

Switch/dim sensor

 in the 

Input a

: 

Function

 parameter window. 

In accordance with the parameter setting, this group object can be switched by actuating the input to 

ON, OFF

 or 

TOGGLE

 or 

can be set to 

No reaction

. With toggle, the previous value, e.g. 1, is toggled directly to the value 0. With the TOGGLE setting, 

the group object should be linked with the switch feedback of the dimming actuator (updating of the switching state) via a non-
sending group address. 

 

Note 

The communication object can be written to externally. Thus cyclic sending is interrupted or may not be possible 
depending on the parameter setting. 

No further group objects are visible with the setting. 

 

Telegram value: 

0 = OFF 
1 = ON 

 

12 

Dimming 

Input a: 

Switch/dimming sensor 

4 bit 

DPT 3.007 

C, T 

This group object is enabled if the 

Function

 parameter is set to 

Switch/dim sensor

 in the 

Input a

: 

Function

 parameter window. 

A long operation at the input has the effect that BRIGHTER or DARKER dim telegrams are sent via this communication object 
on the bus. A STOP telegram is sent and the cyclic sending of dim telegrams is stopped at the end of actuation with START-
STOP-DIMMING. 

 

13, 14 

 

 

 

 

Not assigned 

 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands