manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 33

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   31 

Position for sun = 1 (sun) 

Options: 

No reaction 
UP 
DOWN 
STOP 
Receive position via 8-bit values 

This parameter defines the reaction for sun = 1 (sun) in automatic sun protection mode. 

•

 

No reaction

: The current movement is completed.  

•

 

UP

: The blind moves UP. 

•

 

DOWN

: The blind moves DOWN. 

•

 

STOP

: The output is electrically disconnected, i.e. a moving blind is stopped. 

•

 

Receive position via 8-bit values

: The blind moves to the position by receiving an 8-bit value from 

group objects 

Move to pos. for sun [0..255]

 or 

Adjust slat for sun [0...255]

. 

Delay for sun = 1 
in s [0...65,535] 

Options: 

0…60…65,535 

This parameter defines the delay on activation of 

Position for sun = 1

.  

Via this parameter you can, for example, prevent the blind moving UP and DOWN if the sun is only 
overcast for a short period of time. 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands