manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 120

ABB i-bus

®

 KNX 

Planning and application 
 
 

118   2CDC506083D0201 | JRA/S 6.230.3.1 

4.1.2.3 

Determining the current position 

Reference movement 

The Blind/Roller Shutter Actuator continuously determines the current position of the blind and the slat 
angle based on the duration of the individual movements. For various reasons, over extended periods 
slight inaccuracies can occur in the determination of the position. Therefore, the Blind/Roller Shutter 
Actuator uses the upper and lower end positions to unequivocally determine the current position of the 
blind. Every time the blind is in the upper end position, the position is updated in the blind/shutter actuator 
memory. 

If the end positions are not reached in normal operation, a telegram can be used to trigger a reference 
movement all the way up or down. After a reference movement, the blind remains in the reference position 
or moves back to the stored position – whichever is specified in the parameters. 

Direct and indirect movement to the position 

The 

Move to position

 parameter determines whether a 

Move to position

 telegram moves the blind from its 

current position either directly to the target position, or alternatively triggers a reference movement 
indirectly via a start position (upper end position or lower end position) to a defined target position. 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands