manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 57

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   55 

3.3.2.2.5 

Output A,B: Switch actuator - Forced operation parameter window 

All settings for the 

Forced Operation

 function are undertaken in this parameter window. 

It is visible if the 

Enable function Forced operation

 parameter is enabled in Output A,B: Switch actuator 

(only "UP" contact

)

 parameter window, p. 38. 

 

A Forced operation group object is available for every output. 

The forced operation (a 1 bit or 2 bit communication object per output) sets the output in a defined state, 
where – as long as the forced operation is active – it can only be changed via the communication object 
forced operation. 

The switch state after the end of forced operation can be set using the parameter 

Contact pos. if forced 

operation

. 

•

 

Yes

: The following parameters appear: 

Type of object "Forced operation" 

Options: 

1-bit 
2 bit 

Using the 2-bit group object, the output state is defined directly via the group object value. Control 
of the output via the 

Switch

 group object is disabled as long as the output is forcibly switched ON or 

OFF. 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands