manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 112

ABB i-bus

®

 KNX 

Commissioning 
 
 

110   2CDC506083D0201 | JRA/S 6.230.3.1 

No. 

Function 

Object name 

Data type 

Flags 

78 

Adjust slat 

Blind Output A,B  

 

1 byte 

DPT 5.001 

C, W, T 

This group object is enabled if the 

Mode Output

 parameter is set to 

Blind

 in the 

Output A,B: Mode

 parameter window. 

This group object is used for movement to and feedback of a defined slat position and is therefore only available in Blind 
mode. 

If this group object receives a telegram, the slats are positioned in accordance with the received value. If the blind is currently 
moving, the movement will continue to the target position before the slats are positioned. 

Telegram value: 

0 

 = slats fully OPEN 

…  

= Intermediate position 

255   = slats CLOSED 

 

79 

Reference movement 

Blind Output A,B  

Shutter Output A,B  

1 bit 

DPT 1.008 

C, W 

This group object is enabled if the 

Mode Output

 parameter is set to 

Blind

 in the 

Output A,B: Mode

 parameter window. 

This group object is used to compensate for position deviations, e.g. after frequent UP/DOWN movements to intermediate 
positions. The blinds are moved to the end position (0 = upper, 1 = lower) and back. 

If this group object receives a telegram the blind is moved fully upwards or downwards. 

The current position is stored in order to move the blind to the parametrized position after the reference movement.  
If the option 

Back to stored position

 is set and the 

Automatic

 function was set for the blind before the reference movement,  

it is reactivated after the stored position is reached. 

Telegram value: 

0 = reference movement fully upwards 
1 = reference movement fully downwards 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands