manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 130

ABB i-bus

®

 KNX 

Planning and application 
 
 

128   2CDC506083D0201 | JRA/S 6.230.3.1 

4.2.2.1 

Staircase lighting 

After the staircase lighting time T

ON

 has elapsed, the output switches off automatically. For every telegram 

with the value 1 the time restarts (

Retrigger

 function) unless the parameter 

Extending staircase lighting by 

multiple switch on ("Pumping up")

 in the Output A,B: Switch actuator - Time parameter window, p. 42 is set 

to 

No (not retriggerable)

. 

 

This reaction is the basic reaction of the 

Staircase lighting

 function. 

Via "pumping up" – operation of the push button several times in succession – users can adapt the 
staircase lighting to current needs. The maximum duration of the staircase lighting time can be set in the 
parameters.  

 

If the device receives a further ON telegram while the staircase lighting is switched on, the staircase 
lighting time is added to the remaining period.  

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands