manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 46

ABB i-bus

®

 KNX 

Commissioning 
 
 

44   2CDC506083D0201 | JRA/S 6.230.3.1 

Staircase lighting starts after 
permanent ON is ended 

Options: 

No 
Yes 

•

 

No

: The lighting switches off if 

Permanent ON

 is ended. 

•

 

Yes

: The lighting remains on and the staircase lighting time restarts. 

The function of Permanent ON is controlled via the 

Permanent ON

 communication object value. 

If the communication object receives a telegram with the value 1, the output is switched on 
regardless of the value of the communication object 

Switch

 and remains switched on until the 

communication object 

Permanent ON

 has the value 0. 

Object value "Disable function Time" 
on bus voltage recovery 

Options: 

Unchanged 
1, i.e., disable function Time 
0, i.e., enable function Time 

This parameter defines how the 

Time

 function should react after bus voltage recovery. 

The 

Time

 function can be disabled with a telegram to the 

Disable function Time

 group object.  

•

 

Unchanged:

 The 

Time

 function continues unchanged. 

Note 

The state of the 

Time

 function is stored on bus voltage failure and continues unchanged after 

bus voltage recovery. 

 

•

 

1, i.e., disable function time

: A telegram with the value 1 disables the 

Time

 function. 

Note 

Enabling is only possible via the group object 

Disable function Time

. 

 

•

 

0, i.e., enable function time

: A telegram with the value 0 enables the 

Time

 function. 

Note 

If the staircase lighting is disabled when the function 

Time

 is operational, the light will stay at ON 

until it is switched to OFF manually. 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands