manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 116

ABB i-bus

®

 KNX 

Commissioning 
 
 

114   2CDC506083D0201 | JRA/S 6.230.3.1 

No. 

Function 

Object name 

Data type 

Flags 

87 

Status byte 

Blind Output A,B  

Shutter Output A,B  

1-byte  

C, R, T 

This group object is enabled if the 

Extra feedback

 parameter is set to 

Status byte

 in the 

A, B: Blind

 parameter window. 

This group object provides information about the state of the output and the operation. The information is provided in coded 
format in a 1 byte value. 

The Blind/Roller Shutter Actuator uses this group object to send information concerning the mode in which the output is 
currently operating. Only one mode can be activated at any time. 

The status byte is sent after a change. 

 

Bit sequence: 

76543210 

 

Bit 7:   

not used 

Always: 

0 

 

Bit 6:   

not used 

Always: 

0 

 

Bit 5:  

Safety A 

Telegram value: 

0: inactive 

 

 

1: active 

 

Bit 4:  

Safety B 

Telegram value: 

0: inactive 

 

 

1: active 

 

Bit 3:  

Automatic 

Telegram value: 

0: inactive 

 

 

1: active 

 

Bit 2:  

Sun 

Telegram value: 

0: inactive 

 

 

1: active 

 

Bit 1:  

Upper end position 

Telegram value: 

0: inactive 

 

 

1: active 

 

Bit 0:  

Lower end position 

Telegram value: 

0: inactive 

 

 

1: active 

Special coding for bit 0 and bit 1: 

 

Bit sequence 00: 

Blind between upper and lower end position 

 

Bit sequence 01: 

Lower end position 

 

Bit sequence 10: 

Upper end position 

 

Bit sequence 11: 

Undefined blind position 

 

For further information see: Blind/shutter status byte, p. 142 

 

88 

Status Lower end position 

Blind Output A,B  

Shutter Output A,B  

1 bit 

DPT 1.002 

C, R, T 

This group object is enabled if the 

Extra feedback

 parameter is set to 

End positions

 in the 

A, B: Blind/Shutter

 parameter 

window respectively. 

This group object defines whether the blind is or is not in the lower end position. The group object value is sent about five 
seconds after completion of a movement. 

Telegram value: 

1 = blind in lower end position. 
0 = blind not in lower end position 

 

Note 

After a download or ETS reset, the blind/shutter position is unknown and a 1 is sent to the 

Status Upper end position

 

and 

Status Lower end position

 objects. 

 

 

 
 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands