manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 90

ABB i-bus

®

 KNX 

Commissioning 
 
 

88   2CDC506083D0201 | JRA/S 6.230.3.1 

What is the minimum signal duration? 

In contrast to the debounce time, a telegram is only sent after the minimum signal duration has 
elapsed. The individual functions are: 

If an edge is detected on the input, the minimum signal duration will commence. No telegrams are 
sent on the bus at this time. The signal on the input is observed within the minimum signal duration. 
If a further edge appears at the input during the minimum signal duration, it will be interpreted as a 
new operation, and the minimum signal duration restarts. If no further edges occur after the start of 
the minimum signal duration, a telegram is sent on the bus after the minimum signal duration has 
elapsed. 

Example: Minimum signal duration of the input signal for a detected edge: 

 

In only two cases do no further edge changes occur within the minimum signal duration T

M

 after a 

change of edge. For this reason, only both of these are detected as valid. 

Scan input after download, 
ETS reset and bus voltage recovery 

Options: 

No 
Yes 

•

 

No

: The object value is not scanned after a download, bus reset or bus voltage recovery. 

•

 

Yes

: The object value is scanned after a download, bus reset or bus voltage recovery. The following 

parameter appears: 

Inactive wait state after bus 
voltage recovery in s [0…30,000] 

Options: 

0…30,000 

Here the waiting time after a bus voltage recovery is set. After the waiting time has elapsed the 
state on the input terminals is scanned. The input reacts as if the state on the input terminals has 
just changed. 

Note 

The inactive waiting time does not add to the actual, adjustable sending delay time. This can be 
set separately. 

 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands