manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 117

ABB i-bus

®

 KNX 

Planning and application 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   115 

4 

Planning and application 

In this chapter you will find some tips and application examples for practical use of the device. 

 

4.1 

Output A,B 

This chapter explains the drive types and application examples for Output A,B. 

 

4.1.1 

Drive types 

Output A,B can control two drive types – blind or shutter: 

1.  Blind 

The drive moves the blind UP/DOWN and OPENs/CLOSEs slat adjustment. 

2.  Shutter 

The drive moves the shutter UP and DOWN. In contrast to the blind drive type, there are no group objects 
available for slat control.  

 

4.1.2 

General functions 

The general functions of the blind and shutter are the same. Therefore they are explained below based on 
the blind settings.  

 

4.1.2.1 

Travel times 

Total travel time 

The total travel time is the time that a blind requires to move from fully upwards to fully downwards.  
Should the Blind/Roller Shutter Actuator receive an UP or DOWN Move telegram, the corresponding 
output is switched and the blind is moved in the appropriate direction. 

 

The blind is moved in this direction until the Blind/Roller Shutter Actuator receives a STOP telegram or 
the upper or lower end positions are reached and the motor is switched off by the limit switch. 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands