manualshive.com logo in svg

ABB i-bus KNX JRA/S 6.230.3.1, Product Manual

Share
Download
ABB i-bus KNX JRA/S 6.230.3.1 Product Manual Download Page 49

ABB i-bus

®

 KNX 

Commissioning 
 
 

JRA/S 6.230.3.1 | 2CDC506083D0201   47 

3.3.2.2.2 

Output A,B: Switch actuator - Time, Flashing parameter window 

All settings for the 

Time

 function – 

Staircase lighting, Switching ON/OFF delay

 and 

flashing

 – are 

undertaken in this parameter window. It is visible if the 

Enable function Time

 parameter is enabled in 

Output A,B: Switch actuator (only "UP" contact

)

 parameter window, p. 38. 

 

 

Observe the contact life span and switching cycles per minute. 

 

Note 

For the contact life and switching operations per minute, see Technical data, p 7 

 

Time function 

Options: 

Staircase lighting 
Switching ON/OFF delay 
Flashing 

This parameter defines the type of 

Time

 function for each output.  

•

 

Staircase lighting

: The staircase lighting is switched via an ON telegram from the output A 

Switch

 

group object, the value of which can be parametrized. The staircase lighting time starts when the 
function is switched on. It is switched off immediately after the staircase lighting time ends. 

Note 

The 

Staircase lighting

 function can also be called via the 

Switch, Logical connection x

 (x = 1, 2) group 

object or with a light scene recall. 

 

•

 

Switching ON/OFF delay

: The output can be switched on or off with a delay via this function. 

Summary of Contents for i-bus KNX JRA/S 6.230.3.1

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands