Zte ZXR10 8900 Series Скачать руководство пользователя страница 26

Страница: 26 / 109

ZXR10 8900 Series Hardware Installation Manual

Cabinet Base Installation Preparation

Prepare necessary instruments and project design material and
installation guide material before cabinet base installation.

�

Engineering Design and Installation Drawing

�

Tools

�

Steel tapeline

For measure cabinet position suit cabinet installation re-
quirement or not, measure adjustable base positioning hole
size, diameter and other measurement.

�

Marking pen

This marks location mark of joint drill on antistatic floor,
and mark installation of expansion bolt drill on floor.

�

Score template

It is supported by shipper. Please prepare it before cabinet
installation.

�

Percussion drill (Φ14 drill bit)

This drills on the floor or on the antistatic floor.

�

Vacuum cleaner

This removes the dust inside the hole after drilled.

�

Rubber hammer

This taps expansion blot for fixed

�

Pad

This adjusts the base level.

�

Torque wrench

This fastens the blots and nuts.

Introduction to Cabinet Base
Installation

There are three modes to install cabinet base,

�

Adjustable base installation mode

�

Install cabinet on floor directly

�

Fixed base installation mode

Confidential and Proprietary Information of ZTE CORPORATION

Содержание ZXR10 8900 Series














































































































Результаты поиска

Содержание ZXR10 8900 Series

Отзывы:

Похожие инструкции для ZXR10 8900 Series

Бренды по названию

Популярные бренды

Zte ZXR10 8900 Series, Руководство по установке оборудования

Результаты поиска

Содержание ZXR10 8900 Series

Отзывы:

Похожие инструкции для ZXR10 8900 Series

Бренды по названию

Популярные бренды