ZIV SW3 Скачать руководство пользователя страница 31

Страница: 31 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

31/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

Changes made with the

set

command are not operative merely because they have been

executed. Effective, immediate use of the changes made is achieved by running the

Apply

command. On the contrary, the

Save

commands entails storing the changes

made permanently, without requiring their immediate use, but applied in the case of an

initialisation.

In this way, the changes are implemented as an operating procedure through the

Apply

command, and after checking that the behaviour is correct, it is saved using the

Save

command. Consequently, in the case of obtaining undesirable results, it is always

possible to eliminate the

Save

command and reboot the equipment to recover the

previous status, even in the case that the changed activated lead to the user not being

able to obtain access.

Access can also be obtained to the console remotely through SSH connection and Telnet.

4.2

HTTP SERVER

The HTTP server included provides access to the HTML pages giving access to all the

configuration data.

The procedures for the effective configuration of the parameters are identical, that is to

say, it is necessary to execute the

Apply

command and/or the

Save

command, as

indicated in the section on using the console, but before running these commands, the

system must be informed that the data have been changed through the

Send

command

(the button is present in all the HTML pages).

The

Apply

and

Save

commands are at the bottom of the tree menu and are only visible

when the user profile has administration rights. FIGURE 18 shows commands indicated.

For information about the

Reboot,

Reflash, Configuration files

and

Event files

commands see sections 5.17, 5.18, 5.19 and 5.20 respectively.

The

Apply

Save

and

Reboot

commands request confirmation of the operation from the

user before it is actually executed.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 31 / 122

Результаты поиска

Содержание SW3

Отзывы: