ZIV SW3 Скачать руководство пользователя страница 101

Страница: 101 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

101/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

remove

This eliminates an item from the matrix of a matrix-type parameter.

Syntax:

swt />

remove

name[nº]

Arguments:

name

Parameter from which the item is to be removed.

nº

(Optional) Order number of the parameter item

Observations

To remove an item from the matrix of a matrix-type

parameter, it is necessary to be in the respective directory

or enter the relative route.

If the order number of the item to be removed is indicated,

that item will be removed. If the number is not indicated,

the last one will be removed.

When removing an item that is not the last one, the other

remaining items will be automatically renumbered.

Examples:

swt />

remove nat[2]

swt />

remove nat

swt /admin>

remove ../nat

restore

This applies the factory configuration.

Syntax:

swt />

restore

Arguments:

Observations

This command can be used irrespective of the directory

where the user is.

Example:

swt />

restore

save

This saves the changes made in configuring the equipment in its permanent

memory. However, these changes will not take effect until the equipment is

rebooted.

Syntax:

swt

/> save

Arguments:

Observations:

This command can be used irrespective of the directory

where the user is.

Example:

swt

/> save

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 101 / 122

Результаты поиска

Содержание SW3

Отзывы: