ZIV SW3 Скачать руководство пользователя страница 38

Страница: 38 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

38/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

Telnet and SSH servers can be disabled, although by default they are enabled. In addition,

in the case of the SSH server, both the service port and the idle timeout can be configured.

For this last parameter, valid values are 0 to 300 seconds. A value 0 for idle timeout means

that the feature is disabled.

FIGURE 20

Administration

menu configuration page

The procedure for the installation of the certificates is described in section B.4 of

APPENDIX B

Data structure in CLI.

5.3

LAN CONFIGURATION

The

LAN

menu has the IP parameters for the switch administration and management.

The switch also features running as a switch PVLAN (RFC 5517), see section 5.5.

The configuration parameters are the following:

•

Static IP.

When this control is selected, the equipment uses the data provided by the

user in relation to the IP address and its mask. The main IP address and its mask are

obtained automatically through the DHCP server.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 38 / 122

Результаты поиска

Содержание SW3

Отзывы: