ZIV SW3 Скачать руководство пользователя страница 95

Страница: 95 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

95/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

FIGURE 62

Telnet

window

HyperTerminal

can be used as the

Telnet

graphic interface. To do this, when configuring

the connection select

TCP/IP (Winsock)

in the

Connect using

drop down menu

Telnet can also be run from the

Putty

program. Simply, type the IP address of the

equipment in the main window, and press

Open

Whatever the method chosen to establish connection with the equipment, the

equipment

login

prompt will appear

ready for the user to enter the

login

and code for starting the

session (the logins and their respective passwords are the same as in the web interface).

In operating systems like Microsoft Windows 7©, the Telnet client is disabled by default.

To enable it, from the Start button:

Start

→

Control panel

→

All Programmes

, in

Programs and characteristics

, select

Activate or deactivate the Windows characteristics.

Then, in the window of

Characteristics of Windows

, select

Telnet client

, see FIGURE 63.

By pressing

Accept,

the Telnet client of Windows may be used.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 95 / 122

Результаты поиска

Содержание SW3

Отзывы: