ZIV SW3 Скачать руководство пользователя страница 76

Страница: 76 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

76/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

•

Reauthentication attempts (reAuthMax).

It sets the maximum number of tries the

equipment will send to request reauthentication. Valid values are 1 to 10.

•

Quiet time after failure (quietPeriod).

It sets the period of time in which the

equipment will not request new tries once the maximum number of configured tries is

exceeded. Valid values, in seconds, are 1 to 65535.

•

IP address.

It sets the RADIUS server IP address.

•

UDP port.

It sets the UDP port to which the RADIUS client will send requests to the

server. The default value set in the standard is port 1812.

•

Shared secret.

It sets the password to be used to encode the communication with

the RADIUS server.

FIGURE 43

802.1x

submenu configuration page

5.15.2

MAC list

This submenu permits the authorized client MAC address list to be specified. The list may

or may not be activated in each port through the

Security type

parameter.

FIGURE 44

MAC list

submenu configuration page

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 76 / 122

Результаты поиска

Содержание SW3

Отзывы: