ZIV SW3 Скачать руководство пользователя страница 15

Страница: 15 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

15/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

1.5

WARNINGS

1.5.1

Warnings before installing

The installation of the SW3 in Electrical Substations or Secondary

Substations is generically subject to the fulfilment of all the safety measures

and prevention of risks established for this type of work by the electricity

company that will use these devices and the Safety standards (EN 50110).

. In order to install and handle the SW3 the following points must be

complied with:

Only qualified personnel appointed by the electricity company that owns

the installation should carry out the installation and handling of the SW3.

The environment in which it is to operate should be suitable for the SW3,

fulfilling all the conditions indicated in section 1.4.8.

. ZIV will not accept responsibility for any injury to persons, installations or third

parties, caused by the non-fulfilment of points 1 and 2.



Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 15 / 122

Результаты поиска

Содержание SW3

Отзывы: