ZIV SW3 Скачать руководство пользователя страница 65

Страница: 65 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

65/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

•

Minpoll.

Minimum time between requests. The parameter is the exponent of the

power of 2 that corresponds to the minimum period.

•

Maxpoll.

Maximum time between requests. The parameter is the exponent of the

power of 2 that corresponds to the maximum period.

•

Authentication Enable.

This sets whether messages should be sent with

authentication information.

•

Authentication Key.

If the previous option is enabled it determines which of the

authentication keys defined in the previous block is used to authenticate the

message.

•

Low Traffic.

Minimizes the use of the bandwidth that is used for the

synchronization messages.

There is an additional parameter not dependent on the configuration of NTP servers that

sets whether broadcast NTP-type messages will be accepted.

•

Accept broadcast.

Enables the acceptance of NTP messages that are received

with broadcast address.

The SNTP client only supports the configuration of a server, and the necessary parameters

are:

•

IP.

IP address of the NTP server.

•

Poll.

This sets the period of generation of synchronization messages. Valid values

are 1 to 60.

•

Units.

Time unit for the period of generation of synchronization messages. It can

be minutes or hours.

•

Authentication Enable.

This sets whether messages should be sent with

authentication information.

•

Authentication Key.

If the previous option is enabled it determines which of the

authentication keys defined in the previous block is used to authenticate the

message.

•

Timeout.

Maximum waiting period for receiving response to transmitted

synchronization messages. Valid values are 1 to 15 seconds.

5.13

MULTICAST CONFIGURATION

Under normal conditions, multicast traffic propagates automatically on all interfaces

belonging to each VLAN, with client devices that selectively enable the reception of specific

multicast addresses in which they are interested.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 65 / 122

Результаты поиска

Содержание SW3

Отзывы: