ZIV SW3 Скачать руководство пользователя страница 77

Страница: 77 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

77/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

The parameters for creating the MACS list are the following:

•

Tabulate element identifier. Not relevant.

•

Address.

The client MAC address entered in the list. If a range is desired to be

included, the initial address and final address are separated by a hyphen (see

example in the figure).

•

Ports.

Port/s in which the MAC address will be accepted. A group of discreet ports is

configured with the identifier of each one, separated by a comma, without spaces. If

a range is to be included, the initial port identifier and final port identifier are

separated by a dash. The value

any

means the port is not relevant.

•

VLANs.

Numerical identifier of the VLAN defined in the equipment in which the MAC

address will be accepted (VID fields in the

VLANs

menu). A group of discreet vlans

is configured with the identifier of each one, separated by a comma, without spaces.

If a range is to be included, the initial and final vlan identifiers are separated by a

dash. The value

all

means the vlan is not relevant. Example: in equipment with a

vlan1

vlan3

and

vlan4

defined, the group of numerical identifiers will be

1,3,4

The presence of identifiers in the

Ports

parameter and

VLANs

section is not

exclusive. If values for both parameters are specified, the configuration is applied

at the indicated ports that also meet the requirement of belonging to VLANs

configured.

5.16

OTHERS CONFIGURATION

The

Others

menu allows to configure the time that the switch stores the MAC addresses of

inactivity.

FIGURE 45

Others

menu configuration page

MACS:

•

Bridge Age Time.

It sets the maximum time a learned MAC address of inactivity will

remain in the switch MAC address table. Valid values, in seconds, are 15 to 3600.

The default value is 300.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 77 / 122

Результаты поиска

Содержание SW3

Отзывы: