ZIV SW3 Скачать руководство пользователя страница 24

Страница: 24 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

24/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

FIGURE 13

Multimode optical fiber

2.3

100BASE-FX (MULTIMODE, ST) PORTS

In each 100Base-Fx port of this type, upon request, it should have a ST type connector.

The cable required to make the connection should be a fiber optic cable made up of two

multimode optical fibers, one to transmit data and the other to receive it. Each of the fibers

should be 125

μm in diameter. The core and the cladding of the fiber are included in this

diameter, as can be seen in FIGURE 13. The core can be 50

μm or 62.5 μm in diameter.

The wavelength used should be 1300 nm (multimode). The cable length should not be

more than 2 km.

FIGURE 13 shows the most important input and output optical power characteristics

according to the type of multimode fiber used.

All the ST type connectors have a protective cap.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 24 / 122

Результаты поиска

Содержание SW3

Отзывы: