ZIV SW3 Скачать руководство пользователя страница 59

Страница: 59 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

59/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

The password is not shown for security reasons and so when it is changed (

Change

option), it must be entered twice.

Once the

Password

is introduced from the

Change

option, execute the

send

command of said option, and then, if you want the password to be applied and

saved in the equipment,

DO NOT forget

to execute the

apply

and

save

commands from the main menu tree.

SNMP Traps:

•

Enable Traps.

Enables/disables the generation and transmission of spontaneous

messages by the SNMP agent. The agent will send messages of the different events

when the option is selected.

•

Traps SNMPv1/v2c.

Tabulate information allowing several destination devices for

the traps to be defined.

For each of the spontaneous SNMP message addressees, a profile must be

provided, which must be included in the spontaneous message, the SNMP protocol

version with which it will be coded, the IP address of the addressee and the UDP port

to which the messages will be sent. The default value set in the standard is port 162.

It can be changed to adapt to the operating data of each addressee.

The transmission of the messages in a confirmed (

inform

) way is only accepted for

the v2c and v3 versions of the protocol.

•

Trap v1 agent address.

This sets the IP address the agent will communicate as

being its own when sending spontaneous messages. This parameter is only used to

create the traps when using SNMPv1.

•

Traps SNMPv3.

Tabulate information allowing several destination devices for the

notifications to be defined.

The receivers are identified by means of their IP address and the UDP port to which

the notifications are to be sent. The standard UDP port for the SNMP notifications is

the 162, being the default value.

The

Type

control is used to set whether the transmission of the notifications is

carried out in an unconfirmed (

trap

) or confirmed (

inform

) way.

•

Enable LLDP Trap.

Indicates the SNMP agent whether the notifications created by

the LLDP agent are allowed or not.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 59 / 122

Результаты поиска

Содержание SW3

Отзывы: