ZIV SW3 Скачать руководство пользователя страница 61

Страница: 61 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

61/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

•

Max Age.

The maximum time during which the device considers the last BPDU

message received as valid. In the case of the stipulated time expiring, the device

assumes there has been a topological change and initiates the topological change

communication process. The default value is 20 seconds, and valid values are 6 to

40 seconds.

•

Hello Time.

This parameter sets the time between sending BPDU messages (the

STP protocol messages). The default and maximum value is 2 seconds.

•

Forward Delay.

This parameter is the maximum period of time for an interface to be

in the listening and learning states. The default value for this period is 15 seconds,

and valid values are 4 to 30 seconds.

•

Tx Hold Count.

This sets the maximum number of BPDU packets that can be

transmitted in one second. The default value is 6 and valid values are 1 to 10.

FIGURE 33

STP

menu configuration page

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 61 / 122

Результаты поиска

Содержание SW3

Отзывы: