ZIV SW3 Скачать руководство пользователя страница 97

Страница: 97 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

97/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

TABLE 2

Full list of CLI user console commands

Command Description

User

admin guest

add

Adds a new item to a matrix-type parameter

✓



apply

Applies the new configuration

✓



Changes the directory in the parameters tree

✓

clear

Deletes the statistics

✓



date

Shows the date stored in the equipment

✓



download

Generates a configuration commands file

✓

exit

Interrupts the connection with the equipment

✓

get

Shows the parameter values

✓

help

Shows the list of available commands

✓

log

Shows the log file in use (current)

✓

Shows the lists of available parameters in the current directory

✓

ping

Sends a ping to the indicated host

✓

quit

Interrupts the connection with the equipment

reboot

Reboots the equipment

✓



reload

Loads a previously-saved configuration

✓



remove

Eliminates an item from a matrix-type parameter

✓



restore

Loads a default configuration

✓



save

Saves all the changes made during the session

✓



set

Modifies the value of a parameter

✓



show

Allows the query of the log file in use and of the old log files. It
also allows to display the file containing the customer default
configuration.

✓

stats

Allows to obtain the status parameters of the equipment.

✓

tail

It is useful for monitoring the equipment during operation. It
shows the list of events stored in the log file in use and it
remains to show events as they occur. It closes with Ctrl+C.

✓

telnet

Open a telnet session without interrupting the connection with
the equipment.

✓

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 97 / 122

Результаты поиска

Содержание SW3

Отзывы: