ZIV SW3 Скачать руководство пользователя страница 39

Страница: 39 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

39/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

•

IP address.

It sets the switch IP address.

•

IP mask.

It sets the mask associated with the switch IP address.

•

VLAN id.

VLAN numeric identifier. When configuring multiple VLANs, this parameter

specifies where the equipment will be accessed for management. It is configured

with the value 1 by default, that is, management will be accessed from the interfaces

assigned to the

vlan1

•

Default gateway.

This sets the default router IP address (Default Gateway).

•

MAC address.

It shows the own Ethernet MAC address of the switch.

FIGURE 21

LAN

menu configuration page

5.4

ETHERNET PORTS CONFIGURATION

The

Ports

menu permits the configuration of the operating parameters of the Gigabit/Fast

Ethernet ports of the equipment, and the assigning of each port to the VLANs defined in the

equipment (see section 5.5).

The switch also features running as a switch PVLAN (RFC 5517), see section 5.5.

The page related to the

Ports

menu has two well differentiated sections, which are

described below.

Ports:

•

It identifies the port number, and it coincides with the equipment connector

number. Ports 9 and 10 are always associated with the SFP ports.

•

Enable.

This permits a port to be enabled or disabled, by ticking or not ticking the

respective

Enable

box.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 39 / 122

Результаты поиска

Содержание SW3

Отзывы: