ZIV SW3 Скачать руководство пользователя страница 47

Страница: 47 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

47/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

Private VLAN:

The PVLAN operation is configured in this section. PVLAN allow the user to employ a

single IP address range for a whole L2 domain while keeping privacy among different

VLANs.

PVLAN defines three types of VLAN: Primary, Isolated and Community. To these three

standard types, a fourth special type called Isolated Community has been added.

There are five behaviours for the interfaces: Promiscuous, Isolated, Community, Isolated

Community and Trunk. The first four are for the four types of VLAN indicated, whilst the fifth

allows the operating space to include more than one device.

The traffic which can flow between all these ports are conditioned by the behaviour

assigned to the following table.

Output port

Isolated

Promiscuous

Community

Isolated

Community

Trunk

t p

ort

Isolated

YES

Promiscuous

YES

Community

YES

YES for

ports sharing

community

YES

Isolated

Community

YES

YES for ports

sharing

community

YES

Trunk

(1)

YES

YES for

ports sharing

community

(1)

YES

The VLAN definition operates in the usual way, each one having its own IP address, mask,

etc. It is necessary to register all the vlan that will be used in the device, even those that are

desired to be processed only at level 2 or in transit.

User has special fields to identify Primary VLAN, Isolated and Isolated Communities, see

FIGURE 23. Any VLAN defined different from selected ones for Primary, Isolated or one of

the Isolated Communities will be considered to be Community.

Each

Edge

port behaves accordingly to which VLAN is included. Trunk ports are configured

selecting

Trunk

function to them.

Traffic received from a Trunk will be denied if it belongs to an Isolated Community VLAN. It will only be permitted if it

belongs to the primary VLAN.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 47 / 122

Результаты поиска

Содержание SW3

Отзывы: