ZIV SW3 Скачать руководство пользователя страница 102

Страница: 102 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

102/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

set

This changes the value stored in the configuration parameters or in the

attributes of an item in a matrix-type parameter.

Syntax

swt />

set

[name][[nº][/name2]]

Arguments:

name

name of the parameter to be changed.

nº

item number of a matrix-type parameter.

name2

name of an attribute in a matrix-type parameter.

Observations

When this command is executed the system waits for the

new value to be entered.

The parameter to be changed must be in the current

directory or its relative route must be entered.

In the case of wanting to change the value of any attribute

in the item of a matrix-type parameter, the argument must

include the parameter name, the item number and the

attribute number.

Special attention should be paid when entering the

arguments of this command, as if no argument is

indicated the system will request the new value of each

of the parameters in the active directory and its

subdirectories, one by one. Consequently, if the

set

command is executed without an argument in the root

directory, the system will request a new value for all the

equipment configuration parameters.

If the

set

command is applied to a matrix-type parameter

without indicating the attribute to be modified, the

system will request a new value for each attribute of the

indicated item. If the item number is omitted, the new

values entered for each attribute will be applied to the

last item in the matrix.

Examples:

swt /main>

set hostname

swt />

set main/hostname

swt /admin>

set ../main/hostname

swt />

set nat[2]/origin

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 102 / 122

Результаты поиска

Содержание SW3

Отзывы: