ZIV SW3 Скачать руководство пользователя страница 41

Страница: 41 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

41/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

QinQ Core.

All frames are

always

transmitted

with double tag (Double tagged)

. It

is the specific mode for the connection to a third-party network from which a privative

tag has been obtained.

QinQ Access.

All frames are

always

transmitted with

tag

. It is the specific mode for

the interface that accepts the traffic that will be transmitted to a third-party network

using double tagging.

•

Mode.

This specifies the type of operation for the port in terms of data rate and

operation mode.

Auto

(autonegotiation): Recommended and default value.

10fdx:

10 Mbit/s Full-duplex.

100fdx:

100 Mbit/s Full-duplex.

10hdx:

10 Mbit/s Half-duplex.

100hdx:

100 Mbit/s Half-duplex.

If an operation mode other than

Auto

is configured, both ends of the link must be

identically configured.

For

100Base-Fx ports,

only values

100 Mbit/s Full-duplex (100fdx)

and

100 Mbit/s Half-duplex (100hdx)

have sense, so any value other than 100hdx is

processed as 100fdx.

The

SFP

interfaces

do not support changing data rate

, that is to say,

they

can

operate at the data rate set by the manufacturer

, so that the field value does

not affect to the operation of the SFP interfaces

•

VID (VLAN id by default)

. VLAN numeric identifier in which the port is included. It is

also the VLAN identifier to be assigned to the frames received in the port that is

untagged, or when the tag includes only the priority (priority tagged). The VLAN

definition is selected from the

VLANs

menu, see section 5.5.

For the interfaces operating in QinQ Access mode, the value of this parameter

determines the VLAN identifier to be included in the most outer tag on the

interfaces with double tag, the so-called S-Tag.

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 41 / 122

Результаты поиска

Содержание SW3

Отзывы: