ZIV SW3 Скачать руководство пользователя страница 78

Страница: 78 / 122

SW3

GIGABIT/FAST ETHERNET SWITCH TYPE SW3 (DIN)

78/122

USER GUIDE - M0SW3D1905Iv04 - V04 May 2019

5.17

REBOOT

The equipment can be rebooted by running the

Reboot

command, through the console or

through the HTML pages. The command is available only for the administrator profile.

5.18

CODE REFLASH

The equipment admits the updating of applicative software by running the

Reflash

command, which is only available in the HTML pages and for the administrator profile.

The code reflash process does not alter the configuration data, unless this is expressly

indicated. Nevertheless, once terminated, it entails a momentary loss of service due to

the automatic rebooting of the unit.

A binary image is necessary, which can be selected by pressing the button

Examine

After having selected the image, the update is executed by pressing

Reflash

. The process

usually takes about 5 minutes, during which time the results of the different steps are

displayed in the HTML browser window, but depending on the browser, it is possible that

only the result at the end of the process is shown.

The

Only verify

option allows users to check that the code saved is coincident with the

binary image selected without affecting the installed image.

FIGURE 46

Reflash

configuration page

Содержание SW3



























































































































Результаты поиска

Содержание SW3

Отзывы:

ZIV SW3, Руководство пользователя, Страница: 78 / 122

Результаты поиска

Содержание SW3

Отзывы: