Zeiss Axioskop 40 Скачать руководство пользователя страница 86

Страница: 86 / 146

OPERATION

Axioskop 40

Carl Zeiss

Axioskop 40 FL operation and function controls

Axioskop 40 FL

3-12

B 40-810 e 12/01

Compartment for filter slider (3-7/5)

−

For 3-position or 6-position filter slider with 18 mm filter diameter.

Centering screws for aperture diaphragm (incident light) (3-7/6)

−

Center the aperture diaphragm with an SW 3 ball-headed screwdriver (also see Section 3.5.7).

Push rod for aperture diaphragm (incident light) (3-7/7)

−

Infinitely variabe setting of the aperture diaphragm diameter (see Section 3.5.7).

−

Push rod pushed in:

fully open

−

Push rod pulled out:

locked

Adjustment guide for lamp adjustment (3-7/8)

−

The adjustment guide is used to adjust and center the HBO 100 and HBO 50 fluorescence illuminators

Light intensity regulator (3-7/9)

−

Regulates the direct-current voltage supply for the halogen illuminator in the range from approx. 3 to
12 V.

On / Off switch with control display (3-7/10)

−

Position 0 = Instrument turned off.

−

Position 1 = Instrument turned on, display glows green when the instrument is turned on.

Focusing drive - rough adjustment (rough drive) (3-7/11)

−

Focusing drive for rough adjustment available on either side of the instrument:

−

1 rough rotation = approx. 5 mm

−

Overall lift: approx. 24 mm

Focusing drive - fine adjustment (fine drive) (3-7/12)

−

Focusing drive for fine adjustment available on either side of the instrument:

−

1 fine rotation = 0.1 rough rotation

Color temperature key 3200 K (3-7/13)

−

With the conversion filter switched on and full lamp voltage (12 V), the color temperature comes to
3200 K. This is required for photomicrography using color films (artificial light).

−

Lever in the front position: conversion filter swiveled out

−

Lever in the back position: conversion filter swiveled in

Drive knob for movement of the mechanical stage in the y direction (3-7/14)

−

Movement of the mechanical stage in the y direction, maximum travel range: 50 mm

−

Adjustable torque (smoothness)

Содержание Axioskop 40



















































































































































Результаты поиска

Содержание Axioskop 40

Отзывы:

Zeiss Axioskop 40, Руководство по эксплуатации, Страница: 86 / 146

Результаты поиска

Содержание Axioskop 40

Отзывы: