Zeiss Axioskop 40 Скачать руководство пользователя страница 131

Страница: 131 / 146

Axioskop 40

CARE, MAINTENANCE, TROUBLESHOOTING AND SERVICE

Axioskop 40 FL

Instrument maintenance

Carl Zeiss

B 40-810 e 12/01

4-3

4.2

Instrument maintenance

4.2.1

Performing checks

•

Take sure to ensure that the instrument complies with the required line voltage (e.g. on the HBO 100
transformer).

•

Check the power cable and plug for defects.

•

If any damage is visible, switch off the instrument. Have the instrument repaired only by a qualified
technician.

•

Ensure that the maximum operation time of the halogen and mercury vapor short-arc lamps is not
exceeded.

4.2.2

Changing fuses

Always pull the power plug before
changing the fuses.

The fuse compartment is on the back of the
microscope. It is combined with the instrument
socket and contains two

T 1 A/H 250 V

fuses.

•

Pull the power plug.

•

Pull out fuse holder (4-1/

) until it can be folded

down.

•

Remove the fuses from the holder upwards and
insert new fuses.

•

Fold up the fuse holder and push it back into
the compartment as far as it will go.

•

Insert the power plug in the outlet.

Fig. 4-1

Changing fuses

Содержание Axioskop 40



















































































































































Результаты поиска

Содержание Axioskop 40

Отзывы:

Zeiss Axioskop 40, Руководство по эксплуатации, Страница: 131 / 146

Результаты поиска

Содержание Axioskop 40

Отзывы: