Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 41 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

7.0

RUNNING THE DECODER

The Z3-MVE-150 can also be configured as a video decoder. To see an example of this follow the steps
below.

7.1

Set to Decoder Mode

(1)

Connect an Ethernet cable from “Ethernet” on the back of the unit to a switch, router or other DHCP

server on the same network as your Windows PC. You will use this PC to control the Z3-MVE-150 and
to decode the output stream.

(2)

Connect the AC power supply and turn on the power switch. It will take 45-60 seconds to boot.

(3)

Follow the steps in Sections 6.3 to access the user interface.

(4)

Change “Operating Mode” in the lower right corner of any tab to “Decoder” using the dropdown

menu.

See the following Sections 7.2, 7.3 and 7.4 to set the decoder unit to accept a variety of encoded
content formats. See Section 7.5 to output decoded content via HDMI and Section 7.6 to output decoded
content via SDI.

Figure 40 Z3-MVE-250 Rear Panel Decode Setup Connections

(2) Connect

Ethernet

(3) Connect Power

and Turn on
Switch

Figure 41 Changing to Decoder Mode

Change to

“Decoder”

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды