Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 78 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

(3)

Click on “Applications” in the top band of options. On the left column, click on “live” and then

“Incoming Security”. Click “Edit” and then make sure “RTMP Publishing” and “RTSP Publishing” are
both set to “Open” and “Client Restrictions” is set to “No client restrictions.” Then click “Save”:

The Wowza server is now configured to work with your ZEUS



encoder.

*Note:

You can also specify “Require password authentication” for “RTMP Publishing.” In this case,

“Authentication” on the channel tab needs to be enabled and a valid Wowza user name and password
needs to be entered to successfully access Wowza.

If you still run into issues, verify the Firewall on your PC with the Wowza server is turned off.

Figure 70 Wowza Security Settings

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды