Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 74 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

Output Port

AUTO

HDMI

SDI

Where to output video. AUTO picks up from
which port is being utilized. HDMI and SDI
supported.

Channel Controls

stop

Stop current encode session.

start

Start encode session.

clone

Duplicate CH tab (can be used to quickly
copy CH1 values to CH2, for example).

delete

Used to delete excess tabs created by clone.

(status)

IDLE, STOPPED, RUNNING,
POLLING

Current status of the encoder. “POLLING”
indicates “start” was pressed and the
encoder is waiting for valid input data to be
detected.

9.8

The CH2 Tab (Decode)

Create the “CH2” tab by clicking the “+” tab. Please see CH1 values for a detailed explanation.

The CH2 tab will be identical to CH1, except for the default values of various parameters as shown
below:

Parameter

CH1

CH2

Port

5004

5006

Audio Output

OFF

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды