Z3 Technology EUS Z3-MVE-150 Скачать руководство пользователя

Страница: 14 / 79

DOC-USR-0094-08

___________________________________________________________________________________________

Z3 Technology, LLC

♦

100 N 8

ST, STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

6.4

Configure Encoder for UDP Streaming

(9)

Click on the CH1 tab.

(10)

Verify the “Video Source” is set to “HD-SDI” using the dropdown menu.

*Note:

HD-SDI selection supports HD-SDI resolutions and 3G-SDI resolutions.

(11)

Set the “Video Resolution” to “1920x1080” or “Follow Input”.

(12)

Set “Output Format” to “UDP”.

(13)

You can set the “Dest Address” to:

(a)

the IP address of your PC that will be running the VLC media player (in the pictured
example, 192.168.0.6)

(b)

or to a multicast address (An example multicast address would be “225.1.2.3”. If you are
on a shared network, check with your Network Administrator.)

(14)

Make note of the value of “Dest Port” (This will be “5004” by default).

Figure 5 Z3-MVE-150 User Interface System Setup Tab

Содержание EUS Z3-MVE-150
















































































Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды

Z3 Technology EUS Z3-MVE-150, Инструкция пользователя

Результаты поиска

Содержание EUS Z3-MVE-150

Отзывы:

Похожие инструкции для EUS Z3-MVE-150

Бренды по названию

Популярные бренды